Showing 17–32 of 108 results
AltonaLab combinated Temperature and Humidity sensor is a single board with two sensors: – Temperature sensor with LM335. It works in range -20..+100 C, accuracy: 1%. The sensor’s output is 0..5V. The measured output voltage Vout of the sensor can be converted to temperature using the expression below: T = (Vout-2.7315)*100.0 In case, the Vout…
AltonaLab Humidity sensor is an easy to use board, which works in range 0 ~ 100% RH, Accuracy: ±3% RH. The board has a connector with three screws – ground, power +5V and signal output. The measured output voltage Vout of the sensor can be converted to RH using the expression below: Rh = (Vout…
AltonaLab KIT is a box completed with an IoT software, a lot of hardware boards, many well described experiments. AltonaLab software can be installed on Windows XP or next versions, the system requirements are minimal. DotNet or Java are not needed.
Base licence for AltonaLab SCADA software and Numato 2 Channel USB Powered Relay Module
Base licence for AltonaLab SCADA software and Numato 4 Channel USB Powered Relay Module
SCADA Software for hobby use, home automation, education.
AltonaLab Temperature sensor is an easy to use board, which works in range -20..+100 C, accuracy: 1%. The board has a connector with three screws – ground, power +5V and signal output. The measured output voltage Vout of the sensor can be converted to temperature using the expression below: T = (Vout-2.7315)*100.0 In case, the…
The connector board can be used to connect up to four sensors with analog outputs 0..5V to analog inputs (ADC), which work in range 0..3.3V. The board has two power supply connectors, so many boards can be connected cascade. The board has four group of resistor dividers, the resistors are 1.5k 1%, 3.0k 1%, so…
The connector board can be used to connect up to four sensors with analog outputs 0..5V to analog inputs (ADC), which work in range 0..5V. The board has two power supply connectors, so many boards can be connected cascade. The output of every sensor is connected directly to the ADC input, so conversion formula is:…
The connector board can be used to connect up to four contact sensors to digital inputs or analog inputs (ADC), which work in range 0..5V or 0..3.3V. The board has four connector groups, each of them with connectors 0V, In, +Pow. For example, the board is suitable for home security system, with Infrared motion sensors…
For some IoT applications, we use sensors as push button, reed relay (rain sensor uses reed relay), magnet security sensor for windows/doors (MUC sensor).. Usually the output pulse of this kind of sensors is very short and if we read the state of the sensor using board with digital or analog inputs, we can lost…
The Current Sensors are solid state transducers for measuring the current in fans, pumps and other HVAC equipment. Select one of three ranges by moving the jumper on the device to switch between 10A, 20A and 50A. This sensor outputs 0-5V directly and requires no power supply. The signal is proprtional to the average current…
9V-36V to 5V Converter DC-DC 3A
ELBERT V2 is a simple but versatile FPGA Learning/Development board featuring Xilinx Spartan 3A FPGA. An excellent choice for beginners and advance learners for experimenting and learning system design with FPGAs. This development board features Xilinx XC3S50A 144 pin FPGA and USB2 interface for fast and easy configuration download.
KITs33 products 
SCADA Software22 products 
Numato USB GPIO33 products 
Numato USB Relay88 products 
Numato Ethernet55 products 
Numato WiFi11 product 
Numato Bluetooth33 products Numato FPGA Devices77 products 
Numato Relay Boards44 products 
AltonaLab Relays66 products SNMP Controllers11 product Controllers33 products Power supply1212 products Cables55 products Sensors, analog output1212 products Sensors, digital output77 products Sensors, I2C33 products Connector boards33 products Weather11 product Computers44 products Home Irrigation1414 products Home Security11 product Heating/Cooling11 product 